ASME A112.18.1:2005 pdf free download

ASME A112.18.1:2005 pdf free download

Posted by

ASME A112.18.1:2005 pdf free download.Plumbing supply fittings.
ASME A112.18.1 apphes to plumbing supply fittings and accessories located between the supply line stop and the terminal fitting, inclusive, as lollows:
(a) automatic compensating valves for individual waN-mounted showering systems;
(b) bath and shower supply fittings;
(c) bidet supply fittings;
(d) dothes washer supply fittings;
(e) drinking fountain supply fittings;
(0 humidifier supply stops;
(g) kitchen, sink, and lavatory supply fittings;
(h) laundry tub supply fittings;
(i) lawn and sediment faucets;
(j) metering and self-closing supply fittings; and
(k) supply stops.
1.2
Plumbing waste fittings are covered by ASME Al 12.1 8,2/CSA 8125.2.
1.3
Other devices, e.g.. temperature-actuated In-line mixing valves and flexible connectors under continuous pressure, are covered by CSA 8125.3 or other plumbing product Standards
This Standard does not apply to pipes and tubes or pipe and tube fittings.
1-s
In this Standard. “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause Is to separate from the text explanatory or informative material. Notes to tables and figures are considered pan of the table or figure and may be written as requirements.
1.6
The values stated In either SI (metric) or yard/pound units are to be regarded as the standard. SI units are the units of record In Canada
In this Standard, the yard/pound units are shown in parentheses. The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result In non-conformance with this Standard.
AN references to gallons are to US qalons.
For Information on the conversion criteria used in thés Standard, see Annex A.
5.2.2 Corrosion (all substrates and coatings)
5.2.2.1 Performance requirements
一TAEnES8a33话公证滕阿联群强兰
dimension.
not significantly deface or adversely affect the function of the coated part.5.2.2.2Test procedure
5.2.2.2.1
The coated parts shall meet the performance requirements of Clause 5.2.2.1 after being subjected to oneof the folloving corrosion tests:
(a) ASTM G 85(Annex A1—acetic acid): the test duration shall be 8 h for SC-1 and 24 h for SC-2.(b) ASTM B117(neutral salt): this test shall be applicable to SC-2 devices and shall have a durationof 24 h.
(c)ASTM B 368(CASS): this test shall be applicable to SC-2 devices and shall have a duration of 4 h.(d) ASTM B 380 (Corrodkote): this test shall be applicable to SC-2 devices and shall have a duration
of 4 h.
Note: If emore than one test method is specified,the marturfacturer may specitly which method is to be used.SC-1 and SC-2are defired in Ckouse 3.1.
5.2.2.2.2
An SC-1 specimen that passes the SC-2 test shall be considered to have met the requirements ofClause 5.2.2.2.1.
5.2.3 Adhesion
5.2.3.1 Performance requirements
The coating and the separate layers of multi-layer coatings shall be sufficiently adherent to each otherand to the base material to comply with the requirements of one of the adhesion tests specified inClause 5.2.3.2,5.2.3.3, or 5.2.3.4.
5.2.3.2 Electrodeposited and PvD coatings on metals
Specimens shall be tested to and meet the requirements of one of the follawing adhesion tests specified inASTM B S71:
Paragraph 4: burnish test;bParagraph 7: file test;
cParagraph 8: grind-saw test; or(dParagraph 9: heat-quench test.
5.2.3.3 Electrodeposited and PvD coatings on plastics
5.2.3.3.1 Performance requirements
The adhesion of organic coatings shall be evaluated following the procedure specified in Clause 5.2.3.4and shall not be evaluated during the test specified in Clause 5.2.3.3.2.

Leave a Reply

Your email address will not be published. Required fields are marked *