IEC 60317-32:1997 pdf download – Specifications for particular typesof winding wires -” Part 32: Glass-fibre wound, resin or varnish impregnated,bare or enamelled rectangular copper wire, temperature index 155

IEC 60317-32:1997 pdf download – Specifications for particular typesof winding wires -” Part 32: Glass-fibre wound, resin or varnish impregnated,bare or enamelled rectangular copper wire, temperature index 155.
NOTE – For lies type of wire, the heat shock teat is Inapproprete and tharelore a heat shock teniparaliwe cannot be established Consequently, a class based on the requirements for Iernperaltn index and hew shock ten-çerature cannot be speced.
The enameled wire shall be based on one of the follog standards and shall be agreed between purchaser and supplier
IEC 60317-16:1990. SpecificaLions for particular types of winding wires — Part 16: Polyester enamelled rectangular copper wire, class 155
lEG 60317’28:1990, Specifications for particular types of winding wires – Part 28: Polyesterirnide enamelled rectangular copper wire, class 180
lEG 60317-29:1990, Specifications for particular types of winding wires — Pad 29: Polyester or polyesterimide overcoated with polyamide-imide enamelled rectangutar copper wire, class 200
When an enameled wire Is used, it must have a nanim&an class of 130.
The temperature index of the wire is dependent n the type of impregnating agent usea. The impregnating agent applied to the glass-fibre should have a minimum temperature index of 155.
Thu Qtass-ttre covering may be’
al a singte layer of glass fibre,
b) double layer of glasstibre. with one layer applied In the direction opposite to that of the other layer
The range of nominal conckictor dimensions covered by this standard is:
The specified combinations ot width and thicfness as well as the specified widththlckness ratio are given in lEG 60317-0-4.
2 Normative references
The following standarde contain provisions Mich. through reference in this text. constitute provisions of this International Standard. At the time of pubticabon. the e1ions indicated were valid. All standards are subpect to revision, and pailies to agreements based on this International Standard are encouraged to Investigate the possd,ilily of applying the most recant edItions 0, the standards lwdcated below. Members 01 IEC and ISO maintain registers of Ixirrently vaed international standards.
IEC 60317-0-4.1990, SpecifIcations for particular types of winding wires— Part 0: General requirements — Section 4: Glass-fibre wound bare or enamelled rectangular copper wire
IEC 60317-16:1990, SpecifIcations for particular types of winding wires — Part 16: Polyester enamelled rectangular copper wire, class 155
IEC 6031728:1990, Specifications for particular types of winding wires — Part 28: Polyesterirnide enamelled rectangular copper wire, class 180
IEC 60317-29:1990, Specifications for particular types of winding wires — Part 29: Polyester o polyesterimide overcoated with polyamide-imide enamelled rectangular copper wire, class 200
3 Definitions and general notes on methods of test
For definitions end general notes on methods of lest, see clause 3 of IEC 60317-0-4.
In case of inconsistencies between IEC 60317-0-4 and this standard, IEC 60317-32 shall prevail.
4 Dimensions
See ctause 4 of IEC 60317-0-4.
5 Electrical resistance
See clause Sot IEC 60317-0-4.
6 Elongation
See clause 601 IEC 60317-0-4.
7 Springiness
See clause 7o1 PEG 60317-0-4.