IEC 60455-2:1998 pdf download - Resin based reactive compounds used for electrical insulation -Part 2: Methods of test

IEC 60455-2:1998 pdf download – Resin based reactive compounds used for electrical insulation -Part 2: Methods of test

Posted by

IEC 60455-2:1998 pdf download – Resin based reactive compounds used for electrical insulation -Part 2: Methods of test.
This part of lEG 60455 specifies methods of test to be used for testing resin based reactive compounds, their components and cured compounds used for electrical insulation.
2 Normative references
The following normative documents contain provisions which, through reference in this text. constitute provisions of this part of lEG 60455. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 60455 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
IEC 60050(21 2):1 990, International Electrotechnical Vocabulary (1EV) — Chapter 212: Insulating solids, liquids and gases
IEC 60068-2-10:1988, Environmental testing — Part 2: Tests. Test J and guidance: Mould growth
IEC 60093:1980. Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
lEG 60112:1979, Method for determining the comparative and the proof tracking indices of solid insulating materials under moist conditions
IEC 60216-1:1990. Guide for the determination of thermal endurance properties of electrical insulating materials — Part 1: General guidelines for ageing procedures and evaluation of test results
IEC 60216-2:1990. Guide for the determination of thermal endurance properties of electrical insulating materials — Part 2: Choice of test criteria
IEC 60216-3-1:1990, Guide for the determination of thermal endurance properties of electrical insulating materials — Part 3: Instructions for calculating thermal endurance characteristics — Section 1: Calculations using mean values of normally distributed complete data
IEC 60216-3-2:1993, Guide for the determination of thermal endurance properties of electrical insulating materials — Part 3: Instructions for calculating thermal endurance characteristics — Section 2: Calculations for incomplete data: proof test results up to and including the median time to end-point (equal test groups)
IECITR 60216-4-1:1990, Guide for the determination of thermal endurance properties of electrical insulating materials — Part 4: Ageing ovens — Section 1: Single-chamber ovens
IEC 60216-5:1998. Guide for the determination of thermal endurance properties of electrical insulating materials — Part 5: Guidelines for application of thermal endurance characteristics
IEC 60243-1 :1998, Electric strength of insulating materials — Test methods — Part 1: Tests at power frequencies
IEC 60250:1969. Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
IEC 60296:1982. Specification for unused mineral insulating oils for transformers and switch gear
IEC 60426:1973. Test methods for determining electrolytic corrosion with insulating materials
IEC 60455-1:1998. Resin based reactive compounds used for electrical insulation — Part 1:
Definitions and general requirements
IEC 60455-3 (all parts), Specification for solventless polymerisable resinous compounds used for electrical insulation — Part 3: Specifications for individual materials
IEC 60707:1981. Methods of test for the determination of the flammability of solid electrical insulating materials when exposed to an igniting source
IEC 60814:1997. Insulating liquids — Oil-impregnated paper and pressboard — Determination of water by automatic coulometric Karl Fischer titration
PEC 61006:1991, Methods of test for the determination of the glass transition temperature of electrical insulating materials
IEC 61033:1991, Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate
IEC 61099:1992, Specifications for unused synthetic organic esters for electrical purposes
ISO 37:1994, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 62:1980, Plastics — Determination of water absorption
ISO 75 (all parts), Plastics and ebonite — Determination of temperature of deflection under load ISO 175:1981, Plastics — Determination of the effects of liquid chemicals, including water.

Leave a Reply

Your email address will not be published. Required fields are marked *