IEC 61169-31:1999 pdf download - Radio-frequency connectors -Part 31: RF coaxial connectors with inner diameter of outerconductor 1,0 mm (o,039 in) with screw coupling -Characteristic impedance 50 ohms (type 1,0)

IEC 61169-31:1999 pdf download – Radio-frequency connectors -Part 31: RF coaxial connectors with inner diameter of outerconductor 1,0 mm (o,039 in) with screw coupling -Characteristic impedance 50 ohms (type 1,0)

Posted by

IEC 61169-31:1999 pdf download – Radio-frequency connectors -Part 31: RF coaxial connectors with inner diameter of outerconductor 1,0 mm (o,039 in) with screw coupling -Characteristic impedance 50 ohms (type 1,0).
This part of IEC 61169 standardizes the interface and ratings of the type 1,0 r.f. connectors of 50 fl impedance and having a screw coup’ing mechanism.
Those connectors are recommended lot use with semi.rigid and flexible cable and in microwave applications requiring high performance.
These connectors have an operating frequency range of up to 110 6Hz.
1.2 Normative reference
The following normative documents contain provisions which, through relerence in this text, constitute provisions of this part of IEC 61169. For dated references, subsequent amendments to. or revisions of. any of these publicaf ions do not apply However, parties to agreements based on this part of IEC 61169 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies, Members of IEC and ISO maintain registers of currently valid International Standards.
IEC 61169-1:1992. Radio-frequency connectors — Part f: Generic specification — General requirements and measuring methods
2 Interface dimensions
2.1 MatIng ac.
2.1.1 DImensions — Grade 1 connectors
Millimetres are original dimensions.
All undimensioned pictorial configurations are for reference purposes only.
Enter details ot assessment level and the climatic category.
A reproduction of the outline drawing and details of the panel piercing, if applicable. It shall provide the maximum envelope dimensions, also the position of the reference plane and, in the case of a fixed connector, the position of the mounting plane(s) relative to the front face of the connector.
Any maximum panel thickness limitations for fixed connectors shall be stated,
(8) Particulars of all variants covered by the DS. As appropriate, the information shall
include:
• cable types (or sizest applicable to each variant;
• alternative plated or protective finishes;
• details of alternative mounting flanges having either tapped or plain mounting holes:
• details of alternative solder spills or solder buckets including, when applicable, those for use with Microwave Integrated Circuit (MIC) components.
4.4 Performance
(9 Performance data Isting the most important characteristics of the connector taking into account the recommended values in 3.2 of this specification. Deviations from the minimum requirements shall be clearly indicated. Non-applicable parameters shall be marked na”.
4.5 AddItIonal InformatIon
(10) Insert marking and ordering information as appropriate, together with details of related documents and any invoked structural similarity.
4.6 Selection of tests, test conditions and seventies
(11) na shall be used to indicate non-applicable tests. All tests marked “a by the detail specification writer shall be mandatory.
When using the normal procedure with a dedicated BDS, the letter “a” — for applicable – shall be entered in the “Test required’ column against each of the tests indicated as being mandatory in the lest schedule of 3.3 of this specification. Any addilional tests required at the discretion of the specification writer shall also be Indicated by an a.
The specification writer shall also indicate, when necessary, details of deviations from the standard test methods and test conditions, including any relevant deviations given in the test schedule of the sectional specification.
The qualification approval and conformance Inspection shall be such that the NSI shall be satisfied that they are appropriate and in line with those for other connectors within the system providing a reasonably comparable service.

Leave a Reply

Your email address will not be published. Required fields are marked *